Документация

numSubframes = 10;                          % Number of subframes
SNRdB = [-16.1 -12.1 -8.1 -4.1 -0.1];        % SNR range
NTxAnts = 1;                                % Number of transmit antennas

ue = struct;                  % UE config structure
ue.NULRB = 6;                 % 6 resource blocks (1.4 MHz)
ue.CyclicPrefixUL = 'Normal'; % Normal cyclic prefix
ue.Hopping = 'Off';         % No frequency hopping
ue.NCellID = 150;           % Cell id as specified in TS36.104 Appendix A9
ue.Shortened = 0;           % No SRS transmission
ue.NTxAnts = NTxAnts;

% Hybrid Automatic Repeat Request (HARQ)  indicator bit set to one. Only
% one bit is required for PUCCH 1a
ACK = 1;
pucch = struct;  % PUCCH config structure
% Set the size of resources allocated to PUCCH format 2. This affects the
% location of PUCCH 1 transmission
pucch.ResourceSize = 0;
% Delta shift PUCCH parameter as specified in TS36.104 Appendix A9 [ <#8 1> ]
pucch.DeltaShift = 2;
% Number of cyclic shifts used for PUCCH format 1 in resource blocks with a
% mixture of formats 1 and 2. This is the N1cs parameter as specified in
% TS36.104 Appendix A9
pucch.CyclicShifts = 0;
% Vector of PUCCH resource indices for all UEs as specified in TS36.104
% Appendix A9
usersPUCCHindices = [2 1 7 14];
% PUCCH power for all UEs as specified in TS36.104 Appendix A9
usersPUCCHpower = [0 0 -3 3];

channel = struct;                   % Channel config structure
channel.NRxAnts = 2;                % Number of receive antennas
channel.DelayProfile = 'ETU';       % Channel delay profile
channel.DopplerFreq = 70.0;         % Doppler frequency in Hz
channel.MIMOCorrelation = 'Low';    % Low MIMO correlation
channel.NTerms = 16;                % Oscillators used in fading model
channel.ModelType = 'GMEDS';        % Rayleigh fading model type
channel.InitPhase = 'Random';       % Random initial phases
channel.NormalizePathGains = 'On';  % Normalize delay profile power
channel.NormalizeTxAnts = 'On';     % Normalize for transmit antennas

% SC-FDMA modulation information: required to get the sampling rate
info = lteSCFDMAInfo(ue);
channel.SamplingRate = info.SamplingRate;   % Channel sampling rate

% Channel seeds for each of the 4 UEs (arbitrary)
ueChannelSeed = [11 1 7 14];

cec = struct;        % Channel estimation config structure
cec.TimeWindow = 9;  % Time averaging window size in resource elements
cec.FreqWindow = 9;  % Frequency averaging window size in resource elements
cec.InterpType = 'cubic';         % Cubic interpolation
cec.PilotAverage = 'UserDefined'; % Type of pilot averaging

% Preallocate memory for missed detection probability vector
PMISS = zeros(size(SNRdB));
for nSNR = 1:length(SNRdB)

    % Detection failures counter
    missCount = 0;
    falseCount = 0;

    % Noise configuration
    SNR = 10^(SNRdB(nSNR)/20);              % Convert dB to linear
    % The noise added before SC-FDMA demodulation will be amplified by the
    % IFFT. The amplification is the square root of the size of the IFFT.
    % To achieve the desired SNR after demodulation the noise power is
    % normalized by this value. In addition, because real and imaginary
    % parts of the noise are created separately before being combined into
    % complex additive white Gaussian noise, the noise amplitude must be
    % scaled by 1/sqrt(2*ue.NTxAnts) so the generated noise power is 1.
    N = 1/(SNR*sqrt(double(info.Nfft)))/sqrt(2.0*ue.NTxAnts);
    % Set the type of random number generator and its seed to the default
    % value
    rng('default');

    % Subframe and user loops
    % We now enter two further loops to process multiple subframes and
    % create each of the users' transmissions. The fading process time
    % offset, InitTime, is also generated for the current subframe

    offsetused = 0;
    for nsf = 1:numSubframes

        % Channel state information: set the init time to the correct value
        % to guarantee continuity of the fading waveform
        channel.InitTime = (nsf-1)/1000;

        % Loop for each user
        for user = 1:4

            % Create resource grid
            ue.NSubframe = mod(nsf-1,10);
            txgrid = lteULResourceGrid(ue);

            % Configure resource index for this user
            pucch.ResourceIdx = usersPUCCHindices(user);

            % ACK bit to transmit for the 1st (target) user, the PUCCH
            % Format 1 carries the Hybrid ARQ (HARQ) indicator ACK and for
            % other users it carries a random HARQ indicator. As there is a
            % single indicator, the transmissions will be of Format 1a. The
            % PUCCH Format 1 DRS carries no data.
            if (user==1)
                txACK = ACK;
            else
                txACK = randi([0 1],1,1);
            end

            % Generate PUCCH 1 and its DRS
            % Different users have different relative powers
            pucch1Sym = ltePUCCH1(ue,pucch,txACK)* ...
                10^(usersPUCCHpower(user)/20);
            pucch1DRSSym = ltePUCCH1DRS(ue,pucch)* ...
                10^(usersPUCCHpower(user)/20);

            % Generate indices for PUCCH 1 and its DRS
            pucch1Indices = ltePUCCH1Indices(ue,pucch);
            pucch1DRSIndices = ltePUCCH1DRSIndices(ue,pucch);

            % Map PUCCH 1 and PUCCH 1 DRS to the resource grid
            if (~isempty(txACK))
                txgrid(pucch1Indices) = pucch1Sym;
                txgrid(pucch1DRSIndices) = pucch1DRSSym;
            end

            % SC-FDMA modulation
            txwave = lteSCFDMAModulate(ue,txgrid);

            % Channel modeling and superposition of received signals.
            % The additional 25 samples added to the end of the waveform
            % are to cover the range of delays expected from the channel
            % modeling (a combination of implementation delay and channel
            % delay spread). On each iteration of the loop we accumulate
            % the sum of each transmitted signal, simulating the reception
            % of all four users at the base station.
            channel.Seed = ueChannelSeed(user);
            if (user==1)
                rxwave = lteFadingChannel(channel,[txwave; zeros(25,NTxAnts)]);
            else
                rxwave = rxwave + ...
                    lteFadingChannel(channel,[txwave; zeros(25,NTxAnts)]);
            end
        end

        % Receiver

        % Add AWGN noise at the receiver
        noise = N*complex(randn(size(rxwave)),randn(size(rxwave)));
        rxwave = rxwave + noise;

        % Use the resource indices for the user of interest
        pucch.ResourceIdx = usersPUCCHindices(1);

        % Synchronization
        % The uplink frame timing estimate for UE1 is calculated using
        % the PUCCH 1 DRS signals and then used to demodulate the
        % SC-FDMA signal.
        % An offset within the range of delays expected from the channel
        % modeling (a combination of implementation delay and channel
        % delay spread) indicates success.
        offset = lteULFrameOffsetPUCCH1(ue,pucch,rxwave);
        if (offset<25)
            offsetused = offset;
        end

        % SC-FDMA demodulation
        % The resulting grid (rxgrid) is a 3-dimensional matrix. The number
        % of rows represents the number of subcarriers. The number of
        % columns equals the number of SC-FDMA symbols in a subframe. The
        % number of subcarriers and symbols is the same for the returned
        % grid from lteSCFDMADemodulate as the grid passed into
        % lteSCFDMAModulate. The number of planes (3rd dimension) in the
        % grid corresponds to the number of receive antenna.
        rxgrid = lteSCFDMADemodulate(ue,rxwave(1+offsetused:end,:));

        % Channel estimation
        [H,n0] = lteULChannelEstimatePUCCH1(ue,pucch,cec,rxgrid);

        % PUCCH 1 indices for UE of interest
        pucch1Indices = ltePUCCH1Indices(ue,pucch);

        % Extract resource elements (REs) corresponding to the PUCCH 1 from
        % the given subframe across all receive antennas and channel
        % estimates
        [pucch1Rx,pucch1H] = lteExtractResources(pucch1Indices,rxgrid,H);

        % Minimum Mean Squared Error (MMSE) Equalization
        eqgrid = lteULResourceGrid(ue);
        eqgrid(pucch1Indices) = lteEqualizeMMSE(pucch1Rx,pucch1H,n0);

        % PUCCH 1 decoding
        rxACK = ltePUCCH1Decode(ue,pucch,1,eqgrid(pucch1Indices));

        % Detect missed (empty rxACK) or incorrect HARQ-ACK (compare
        % against transmitted ACK.
        if (isempty(rxACK) || any(rxACK~=ACK))
            missCount = missCount + 1;
        end


    end

    PMISS(nSNR) = missCount/numSubframes;

end

plot(SNRdB,PMISS,'b-o','LineWidth',2,'MarkerSize',7);
grid on;
hold on;
plot(-4.1,0.01,'rx','LineWidth',2,'MarkerSize',7);
xlabel('SNR (dB)');
ylabel('Probability of ACK missed detection');
title('Multi user PUCCH Format 1a test (TS36.104 Section 8.3.4.1)');
axis([SNRdB(1)-0.1 SNRdB(end)+0.1 -0.05 0.4]);
legend('simulated performance','target');